The TreeChopper
The TREECHOPPER is designed and manufactured by ATV-X, Inc. and attaches to most All Terrain Vehicles (ATVs). Its simple yet effective design allows the TREECHOPPER to float over even the roughest terrain while cutting a variety of unwanted trees and vegetation. By utilizing an ATV as the workhorse, the TREECHOPPER can cut trees quickly in a variety of conditions and environments.

The TREECHOPPER can safely cut trees up to four inches in diameter and very close to ground level which is necessary to lessen the possibility of re-growth.

The TREECHOPPER takes the labor out of tree growth management and puts fun back into work!

Some grinding or flattening of the ATV mounting area may be required. This is done to insure that the mounting bracket fits securely to the frame of the ATV. It may be necessary to drill holes through the mounting bracket and the ATV frame/skid plate.

The mounting bracket must be fastened tight to the frame or metal skid plate. If there is a plastic skid plate between the bracket and the frame it will need to be removed so that the bracket tightens flat against the ATV frame.

Safety

Carefully read this manual and your ATV manual. Failure to follow the warnings contained in this manual and your ATV manual can result in severe injury or death.

Always start out cutting small trees. Remember the TreeChopper is designed to cut small trees at early stages of growth.

-	Read Safety Decals Carefully and follow instruction on safety decals.
-	Learn how to properly operate your ATV prior to using the TreeChopper.
-	Operate the TreeChopper only when there is good, clear visibility of the cutting area.
-	Keep Children and others away when operating the TreeChopper.
-	Do Not Let Persons under the Age of 16 operate the TreeChopper?
-	Always wear Personal Protective Equipment (PPE) like safety shoes/boots, gloves, protective eyewear, and clothing when operating the TreeChopper.
-	Keep all guards and shields in place when the Tree Chopper is not in use.
-	Prior to use check the TreeChopper to be sure all blots are tight and the blades are properly adjusted.
-	Always use a heavy duty trailer to transport your ATV and TreeChopper. When transporting by trailer always lower the TreeChopper to the trailer deck.
-	Securely fasten the ATV and TreeChopper to the trailer with straps, chains, or cables.
-	Do not attempt to cut Trees with trunks larger than a 4 inch diameter.
-	Approach trees to be cut from a safe distance, approximately 10 feet.
-	Approach tree at a safe speed and accelerate through the tree during cutting.
-	Always follow ATV warning and riding instructions.

Operation

The TreeChopper can be raised and lowered by attaching a lifting device (winch, ratchet strap, chain) and using the hook on the chassis. This allows for quicker travel to and from the cutting areas while the TreeChopper is in the raised position

Thee TreeChopper cuts by lining up so that the trunk of the tree is center to the cutting blades. Once the tree trunk is centered and you have cleared the area of debris you are ready to cut.

You approach the tree from approximately 6 to 10 feet. Accelerate the ATV in forward motion through the tree. Impact should be minimal. Once you have gained confidence and experience with the tree trunks 2 inches diameter and less you should be ready to cut bigger tree trunks of up to 4 inches.

Parts and Service

Parts may be ordered through your dealer or by contacting ATV-X Inc.

The TreeChopper should require very little service. It is important to keep the cutting blades clear of debris when in use. Before cleaning the blades you simply lower the TreeChopper to the ground, stop the ATV, and turn off the ignition. Then carefully remove any stuck debris making sure to avoid hand or foot contact with the blades.

After cutting, wash the TreeChopper with low pressure water spray and then use lubricating oil on the blades to prevent rusting.

It is recommended that all major service work such as blade replacement be performed by a factory certified dealer.

Warranty

Limited Warranty is provided for customers who operate and maintain their equipment as described in this manual.

Limited Warranty
ATV-X Inc. gives a SIX MONTH LIMITED WARRANTY on all components of the TreeChopper against defects in material or workmanship. This warranty covers the parts and labor charges for repair or replacement of defective parts which are covered by this warranty. This warranty begins on the date of purchase. The warranty is not transferable to another consumer during the warranty period.

Registration
At the time of sale, the Warranty Registration Form must be completed by the purchaser and returned to ATV-X within ten days. Upon receipt of this registration ATV-X will record the registration for warranty. No verification will be sent to the purchaser as the copy of the Warranty Registration will be the warranty entitlement. NO WARRANTY COVERAGE WILL BE ALLOWED UNLESS YOUR TREECHOPPER IS REGISTERED WITH ATV-X.

Initial installation is very important in ensuring trouble-free operation. Refer to the Operations Manual for installation instructions.